filename: TFS1227C.doc version 2.1 21.03.2013 vectron international filter specification tfs 1227 c 1/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. measurement condition ambient temperature: 23 c input power level: 0 dbm terminating impedance: input: 200 output: 200 characteristics remark: the maximum attenuation in the passband is defined as the insertion loss a e . the nominal frequency f n is fixed at 1227.6 mhz without any tolerance or limit. the values of absolute attenuation a abs are guaranteed for the whole operating temperature range. the frequency shift of the filter in the op erating temperature range is included in the production tol erance scheme. d a t a typ. value tolerance / limit insertion loss in pb a e 1.5 db max. 3.5 db nominal frequency f n - 1227.6 mhz passband pb - f n 10.0 mhz passband variation 0.4 db max. 2.0 db absolute attenuation a abs 0.3 mhz ? 1177 mhz 30 db min. 28 db 1277 mhz ? 2500 mhz 33 db min. 30 db group delay ripple within pb 7 ns max. 12 ns group delay variation (unit to unit) * +/-2 ns max. +/-5 ns vswr within pb 1.9 : 1 max. 2.3 : 1 input power level in pb - max. 20 dbm operating temperature range otr - - 40 c ... + 85c storage temperature range - - 45 c ... + 85c temperature coefficient of frequency tc f ** -49 ppm/k *) measured at: f n , f n + 10 mhz , f n - 10 mhz **) ? f c (hz) = tc f (ppm/k) x (t - t o ) x f cat (mhz) generated: checked / approved:
filename: TFS1227C.doc version 2.1 21.03.2013 vectron international filter specification tfs 1227 c 2/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. filter characteristic 1197.6 1207.6 1217.6 1227.6 1237.6 1247.6 1257.6 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 frequency in mhz magnitude in db 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 delay in s 0 500 1000 1500 2000 2500 -40 -30 -20 -10 0 frequency in mhz magnitude in db construction and pin connection (all dimensions in mm) 1 2 3 5 6 7 4 8 1,2 max. 0,6 3,0 +/-0,15 0,6 1,5 0,6 6 0 g r d . 1 3 7 5 date code 200 test circuit c27c d12 1 input 1 2 input 2 3 ground 4 ground 5 output 2 6 output 1 7 ground 8 ground date code: year + week d 2013 e 2014 f 2015 ... saw 3, 4, 7, 8 2 5 6 1
filename: TFS1227C.doc version 2.1 21.03.2013 vectron international filter specification tfs 1227 c 3/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. stability characteristics, reliability after the following tests the filter shall meet the whole specification: 1. shock: 500g, 1 ms, half sine wave, 3 shocks each plane; din iec 68 t2 - 27 2. vibration: 10 hz to 500 hz, 0,35 mm or 5 g respe ctively, 1 octave per min, 10 cycles per plane, 3 p lanes; din iec 68 t2 - 6 3. change of temperature: -55 c to 125c / 30 min. each / 1 0 cycles din iec 68 part 2 ? 14 test n 4. resistance to solder heat (reflow): reflow possible: three ti mes max.; for temperature conditions refer to the attached " air reflow temperature conditions" on page 4; this filter is rohs compliant (2002/95/eg, 2005/618 /eg) packing tape & reel: iec 286 ? 3, with exception of value f or n and minimum bending radius; tape type ii, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 3000 reel of empty components at start: min. 300 mm reel of empty components at start including leader : min. 500 mm trailer: min. 300 mm g do w ct f e g d1 p2 p1 po bo ao pull off direction pin marker typ date code ko t a c n w 1 w 2 the minimum bending radius is 45 mm. tape (all dimensions in mm) w : 8,00 0,3 po : 4,00 0,1 do : 1,50 +0,1/-0 e : 1,75 0,1 f : 3,50 0,05 g(min) : 0,75 p2 : 2,00 0,05 p1 : 4,00 0,1 d1(min) : 1,50 ao : 3,25 0,1 bo : 3,25 0,1 ct : 5,3 0,1 reel (all dimensions in mm) a : 180 w1 : 8,4 +1,5/-0 w2(max) : 14,4 n(min) : 60 c : 13,0 0,2
filename: TFS1227C.doc version 2.1 21.03.2013 vectron international filter specification tfs 1227 c 4/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. air reflow temperature conditions conditions exposure average ramp-up rate (30c to 217c) less than 3c/ second > 100c between 300 and 600 seconds > 150c between 240 and 500 seconds > 217c between 30 and 150 seconds peak temperature max. 260c time within 5c of actual peak temperature between 10 and 30 seconds cool-down rate (peak to 50c) less than 6c/second time from 30c to peak temperature no greater than 300 seconds temperature / c time / s max. 260c 217c 10 ... 30 s 30 ... 150 s max. 300 s chip-mount air reflow profile
filename: TFS1227C.doc version 2.1 21.03.2013 vectron international filter specification tfs 1227 c 5/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. history version reason of changes name date 1.0 generation of development specification noack 20.06.2011 2.0 - absolute attenuation updated (0,3 mhz ? 1 177 mhz) molke 25.10.2012 - group delay variation from unit to unit correc ted (f c f n ) 2.1 - change from development spec to filter spec molke 21.03.2013 - typical values added - filter characteristic added
|
